A typical problem in every household is when the toilet doesn’t flush with force as it was before. But the water must flow at the full pace to clean the waste properly. Otherwise, having a lousy smell, in the whole bathroom is going to feel everyone uncomfortable
And when there is a guest in the house, this is going to be a scene embarrassment. Nonetheless, it will also cause illness to your families. Therefore, taking the necessary steps to solve the problem inevitable.
Don’t worry, whoever thinking about how can I get my toilet to flush stronger. Because here, this what I am going share with you.
Why Your Toilet Flushes Slowly and Incompletely
Before jumping into the solution, figuring the source of problems of having flush issues would be a wise decision.
There could be multiple or one reasons that causes the issue. Having that identified is going to boost up the speed to solve the problem. So, first, figure out if your question is similar to which one of these that are given below.
Insufficient Water in the Flush
At how much speed your toilet tank is performing the flush mostly depends on the water level in the container you have. If there is a shortage of water in the flush tank, then it is obvious your flush force will be decreased.
Secondly, it might be the reason for blockage or leakage in your toilet system. Remember, there is a chance of clogged after a while of usage, and this another common issue. If the drainage system is not well, making enough force of the flush will be dissolved.
Most people flush the waste through the toilet that they should not. Not every item that we flush wiped away due to nature. And then, that create obstacles in the way of water. In the end, this sort of wastes causes a blockage problem.
If not, then something else
Still, there is a chance of causing the problem by something else if the first two have not. Look into the drain vents. And also investigate the sewage system. Both of these can cause a slow flash problem.
Since this is not the usual content of the book, you might not be able to solve the issue on your own. So call in action any professional is the best decision to take at that moment.
How to Improve Toilet Flush Performance
A bunch of problems could be there, but it does not mean you have to give up on your toilet flush system. You can get rid of the problem if your toilet not flushing strong. So, what would be the solution to your question? Let’s find out.
Check the water level
Time to dig into the first listed problem. First, check the water level is really low or not. If yes, then you need to increase the water level.
Usually, the water level should be a minimum one inch below pipe that is also known as the overflow pipe. It is located at the center of the flush tank. Mark the designation with a pencil.
You have to improve the water level until it comes up onto the mark. Another thing you should remember that your flapper chain must not be too long because that may also cause the problem. Therefore, adjust the height if it is not right.
Solving the clogged issues
Since it is one of the prior problems that you might face regarding your toilet flush, you should focus on solving it first. Hence, identify the source of the clog. It is more likely if you have a clogged problem, then there would be a mess of waste paper in the pipeline.
In that case, still, the water system can work but not at a speed that did previously. To solve the problem, you can use multiple ways.
It is one of the cheapest ways to solve the clogged issue so far. To begin the fight against the clogging issue, first, you have to pour baking soda into the toilet water. The amount should be no more than one cup.
Whenever the soda reaches to the bottom, pour vinegar in the next step. Then wait for the chemical reaction. Both of the chemicals will be fizzed gradually due to nature. Then, keep the situation for the next 2 to 3 hours. After that, check the flush system if it still has anymore clogging problem.
If you find it working correctly at the speed that you are seeking, then you are done with the operation. But if not, you should do the same trick again, but this time with a plunger.
Another low-cost way to solve this problem is to use a household dishwasher. First of all, you would need to heat water. The amount should be at least one gallon. Afterward, pour the regular dish soap in the toilet. Don’t use more than two cups. Keep it for one hour.
At the next step, you need to pour the toilet with warm water. Do this carefully by avoiding any accident to your hands or other parts of your body.
The mix of dish wash and hot water should be able to loosen the clogged state of your toilet. As a result, you will get a full, paced working flush system.
Cleaning jet holes
If you might wonder what this jet hole is, this is actually located under the toilet rim. In addition, the jet holes accumulate the debris and waste significantly throughout use. Since you are using and flushing the toilet regularly for a while, there should be a bulk of waste mineral of water, which might block the speed of flush water.
Therefore, cleaning them with a sponge, wire coat hanger, or any suitable tool would be a great way to revive the flush water speed.
All of the above ways are going to solve the issue by getting your hands dirty. But if they have failed in your case for an unknown reason, then it is time for the aggressive way.
Get a toilet auger online or from your local store. Use the tool for pulling the stuck waste inside the toilet. Try to avoid getting in touch with dirty water while doing the operation.
Frequently Asked Questions
Q: Why does my toilet have a weak flush?
A: The primary reason behind your problem is if your toilet’s siphon jet, or pipe (waste pipe), or jet holes are clogged. Usually, the clogging issue arrives when you are using the toilet for an extended period. Don’t worry, we described the most possible was to convert low flow toilet to high flow.
Q: Do I need to change the toilet system if the flush is not working?
A: It depends on the type of source causing the problem. But whatever it is, you might not need to change the whole system rather than replacing the flush valve or flapper valve if the source is due to the oldy flush system.
Q: Do you need a professional to repair the flush?
A: You might not need to hire any professionals if the problem is related to any of the above discussed. Even you can solve it on your own without costing too much. But if the problem occurs due to the inadequate drainage system of the toilet, then calling a professional is the last way to get the problem solved.
Q: How do I check the water pressure of the toilet flush?
A: You can check the water pressure of the toilet flush with the help of the local water department. In general, the ideal pressure should be 45 to 55 psi. If the pressure rate is above or below the state, there should be urgent practice to solve the issue.
Q: How do you adjust the water-level in the toilet bowl?
A: You can do it by adjusting the valve inside the toilet flush tank. What you have to do is turn the adjustment screw of the valve. You have to do this clockwise in order to raise the water level at the ideal state. Remember to keep the water level below the overflow pipe of the flush tank, at least about one inch.
So, you got the answer regarding how can I get my toilet to flush stronger. Now, neither your toddlers are going to bother you about lousy smell after you use the toilet, nor are you going to shy when calling the next guest home. Hospitality will both will be hygienic and confident, right?
However, I am here to read your experience regarding the above methods I have shared to solve your flush speed problems. Is it working great now? Or are there any more issues regarding other systems of your toilet? Let me know.